View MAX4394ESDT_4522799.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

19-2322; Rev 4; 11/09
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
General Description
The MAX4389/MAX4390/MAX4392-MAX4396 family of op amps are unity-gain stable devices that combine high-speed performance, rail-to-rail outputs, and disable mode. These devices are targeted for applications where an input or an output is exposed to the outside world, such as video and communications. The MAX4389/MAX4390/MAX4392-MAX4396 operate from a single 4.5V to 11V supply or from dual 2.25V to 5.5V supplies. The common-mode input voltage range extends to the negative power-supply rail (ground in single-supply applications). The MAX4389/MAX4390/ MAX4392-MAX4396 consume only 5.5mA of quinescent supply current per amplifier while achieving a 85MHz -3dB bandwidth, 27MHz 0.1dB gain flatness, and a 500V/s slew rate. Disable mode sets the outputs to high impedance while consuming only 450A of current. The MAX4389 single, MAX4393 dual, MAX4394 triple, and MAX4396 quad include disable capabilities. The MAX4389 and MAX4390 are available in ultra-small, 6-pin SC70 packages.
Features
Low Cost High Speed 85MHz -3dB Bandwidth 27MHz 0.1dB Gain Flatness 500V/s Slew Rate Single 4.5V to 11V or Dual 2.25V to 5.5V Operation Rail-to-Rail Outputs Input Common-Mode Range Extends to VEE Low Differential Gain/Phase: 0.015%/0.015 Low Distortion at 5MHz -59dBc Spurious-Free Dynamic Range High Output Drive: 50mA 450A Disable Capability (MAX4389/MAX4393/MAX4394/MAX4396) Space-Saving SC70, SOT23, MAX, or TSSOP Packages
MAX4389/MAX4390/MAX4392-MAX4396
Ordering Information
PART MAX4389EXT+T MAX4389EUT+T MAX4389EUT/V+T MAX4390EXT+T TEMP RANGE -40C to +85C -40C to +85C -40C to +85C -40C to +85C PINPACKAGE 6 SC70 6 SOT23 6 SOT23 6 SC70 TOP MARK ABF ABDC ABDC ABE
Applications
Set-Top Boxes Surveillance Video Systems Analog-to-Digital Converter Interface CCD Imaging Systems Digital Cameras Video-on-Demand Video Line Driver
MAX4390EUK+T -40C to +85C 5 SOT23 ADZM Ordering Information continued at end of data sheet.
Selector Guide appears at end of data sheet. +Denotes a lead(Pb)-free/RoHs-compliant package. /V denotes an automotive qualified part. T = Tape and reel.
Typical Operating Circuit
DISABLE IN 75 MAX4389 Zo = 75 75 OUT
Pin Configurations
TOP VIEW +
OUT 1 6 VCC
VEE 2
MAX4389
5
DISABLE
IN+ 3
200
4
IN-
200
SC70/SOT23
VIDEO LINE DRIVER
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com.
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC to VEE) ..................................-0.3V to +12V IN_+, IN_-, OUT_, DISABLE.............(VEE - 0.3V) to (VCC + 0.3V) Differential Input Voltage ....................................................2.5V Current into Input Pins ......................................................20mA Output Short-Circuit Duration to VCC or VEE (Note 1)................................................Continuous Continuous Power Dissipation (TA = +70C) 5-Pin SOT23 (derate 7.1mW/C above +70C)............571mW 6-Pin SOT23 (derate 8.7mW/C above +70C)............696mW 6-Pin SC70 (derate 3.1mW/C above +70C) ..............245mW Note 1: Continuous power dissipation must also be observed.
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
8-Pin SO (derate 5.88mW/C above +70C)................471mW 8-Pin MAX (derate 4.5mW/C above +70C) .............362mW 10-Pin MAX (derate 5.6mW/C above +70C) ...........444mW 14-Pin SO (derate 8.33mW/C above +70C)..............667mW 14-Pin TSSOP (derate 10mW/C above +70C) ..........727mW 20-Pin TSSOP (derate 10.9mW/C above +70C) .......879mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C
DC ELECTRICAL CHARACTERISTICS--Single Supply
(VCC = 5V, VEE = 0V, VCM = VCC/2, VOUT = VCC/2, RL = to VCC/2, DISABLE_ = VCC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER Input Common-Mode Voltage Range Input Offset Voltage Input Offset Voltage Matching Input Offset Voltage Tempco Input Bias Current Input Offset Current Input Resistance Common-Mode Rejection Ratio Open-Loop Gain TCVOS IB IOS RIN CMRR AVOL Differential mode (-1V VIN +1V) Common mode (-0.2V VCM +2.75V) (VEE - 0.2V) VCM (VCC - 2.25V) 0.25V VOUT 4.75V, RL = 2k 0.8V VOUT 4.5V, RL = 150 1V VOUT 4V, RL = 50 RL = 2k RL = 150 Output Voltage Swing VOUT RL = 75 RL = 75 to ground Output Current Output Short-Circuit Current Open-Loop Output Resistance IOUT ISC ROUT VCC - VOH VOL - VEE VCC - VOH VOL - VEE VCC - VOH VOL - VEE VCC - VOH VOL - VEE 40 40 70 50 50 SYMBOL VCM VOS CONDITIONS Guaranteed by CMRR test TA = +25C TA = -40C to +85C MAX4392-MAX4396 1 15 2.5 0.2 70 3 95 70 60 58 0.065 0.05 0.3 0.25 0.5 0.45 1 0.025 55 50 100 8 0.25 0.15 0.5 0.5 0.8 0.8 1.7 0.1 mA mA V dB 15 5 MIN VEE 0.2 5 TYP MAX VCC 2.25 18 26 UNITS V mV mV V/C A A k M dB
Sinking from RL = 75 to VCC Sourcing into RL = 75 to VEE Sinking or sourcing
2
_______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
DC ELECTRICAL CHARACTERISTICS--Single Supply (continued)
(VCC = 5V, VEE = 0V, VCM = VCC/2, VOUT = VCC/2, RL = to VCC/2, DISABLE_ = VCC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER Power-Supply Rejection Ratio Operating Supply Voltage Range Disabled Output Resistance DISABLE_ Logic-Low Threshold DISABLE_ Logic-High Threshold DISABLE_ Logic Input Low Current DISABLE_ Logic Input High Current Quiescent Supply Current (Per Amplifier) SYMBOL PSRR VS ROUT(OFF) VIL VIH IIL IIH IS DISABLE_ = 0 DISABLE_ = VCC DISABLE_ = VCC DISABLE_ = 0 VCC 1.25 20 5 3.2 0.3 60 40 5 0.4 CONDITIONS VEE = 0V, VCC = 4.5V to 5.5V Guaranteed by PSRR DISABLE_ = 0, 0 VOUT 5V MIN 48 4.5 40 95 VCC - 3 TYP 65 11 MAX UNITS dB V k V V A A mA
MAX4389/MAX4390/MAX4392-MAX4396
DC ELECTRICAL CHARACTERISTICS--Dual Supply
(V CC = 5V, V EE = -5V, V CM = 0V, V OUT = 0V, R L = to 0, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER Input Common-Mode Voltage Input Offset Voltage Input Offset Voltage Matching Input Offset Voltage Tempco Input Bias Current Input Offset Current Input Resistance Common-Mode Rejection Ratio Open-Loop Gain TCVOS IB IOS RIN CMRR AVOL Differential mode (-1V VIN +1V) Common mode (-0.2V VCM +2.75V) VEE VCM (VCC - 2.25V) -4.5V VOUT 4.5V, RL = 2k -4.25V VOUT 4.25V, RL = 150 70 65 50 SYMBOL VCM VOS TA = +25C TA = -40C to +85C MAX4392-MAX4396 1 20 5 0.5 70 3 90 80 60 15 5 CONDITIONS Guaranteed by CMRR test MIN VEE 7 TYP MAX VCC - 2.25 20 28 UNITS V mV mV V/C A A k M dB dB
_______________________________________________________________________________________
3
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
DC ELECTRICAL CHARACTERISTICS--Dual Supply (continued)
(V CC = 5V, V EE = -5V, V CM = 0V, V OUT = 0V, R L = to 0, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER SYMBOL RL = 2k Output Voltage Swing VOUT RL = 150 RL = 75 Output Current Output Short-Circuit Current Open-Loop Output Resistance Power-Supply Rejection Ratio Operating Supply Voltage Range Disabled Output Resistance DISABLE_ Logic-Low Threshold DISABLE_ Logic-High Threshold Quiescent Supply Current (Per Amplifier) IOUT ISC ROUT PSRR VS ROUT(OFF) VIL VIH IS DISABLE_ = VCC DISABLE_ = 0V VCC - 1.25 6 0.45 10 0.8 VEE = 0V, VCC = 4.5V to 5.5V Guaranteed by PSRR DISABLE_ = 0V, -5V VOUT +5V 48 4.5 40 95 VCC - 3 CONDITIONS VCC - VOH VOL - VEE VCC - VOH VOL - VEE VCC - VOH VOL - VEE 50 50 MIN TYP 0.175 0.075 0.575 0.4 1.5 0.75 95 75 100 8 60 11 MAX 0.3 0.2 0.85 1.5 2.35 1.6 mA mA dB V k V V mA V UNITS
Sinking from RL = 75 to VCC Sourcing into RL = 75 to VEE Sinking or sourcing
AC ELECTRICAL CHARACTERISTICS--Single Supply
(V CC = 5V, V EE = 0V, V CM = 1.5V, R L = 100 to V CC /2, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), VOUT = VCC/2, AVCL = 1V/V, TA = +25C, unless otherwise noted.)
PARAMETER Small-Signal -3dB Bandwidth Large-Signal -3dB Bandwidth Small-Signal 0.1dB Gain Flatness Large-Signal 0.1dB Gain Flatness Slew Rate Settling Time to 0.1% Rise/Fall Time Spurious-Free Dynamic Range SYMBOL BWSS BWLS BW0.1dBSS BW0.1dBLS SR ts tR/tF SFDR VOUT = 2VP-P VOUT = 100mVP-P VOUT = 2VP-P VOUT = 2V step VOUT = 2V step VOUT = 100mVP-P fC = 5MHz, VOUT = 2VP-P CONDITIONS VOUT = 100mVP-P MIN TYP 72 80 30 30 500 28 4 -59 MAX UNITS MHz MHz MHz MHz V/s ns ns dBc
4
_______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
AC ELECTRICAL CHARACTERISTICS--Single Supply (continued)
(V CC = 5V, V EE = 0V, V CM = 1.5V, R L = 100 to V CC /2, DISABLE_ = V CC (MAX4389/MAX4393/MAX4394/MAX4396), VOUT = VCC/2, AVCL = 1V/V, TA = +25C, unless otherwise noted.)
PARAMETER Differential Phase Error Differential Gain Error Input Noise-Voltage Density Input Noise-Current Density Input Capacitance Output Impedance Disable OFF Time Disable ON Time Channel-to-Channel Isolation CHISO SYMBOL DP DG en in CIN ZOUT f = 5MHz MAX4389/MAX4393/MAX4394/MAX4396 MAX4389/MAX4393/MAX4394/MAX4396 MAX4392-MAX4396, specified at DC CONDITIONS NTSC, RL = 150 NTSC, RL = 150 f = 10kHz f = 10kHz MIN TYP 0.015 0.015 13 2.1 1 0.6 80 40 -97 MAX UNITS degrees % nV/Hz pA/Hz pF ns ns dB
MAX4389/MAX4390/MAX4392-MAX4396
AC ELECTRICAL CHARACTERISTICS--Dual Supply
(VCC = 5V, VEE = -5V, RL = to GND, GND = 0, VOUT = 0V, Gain = 1V/V, DISABLE = VCC, and TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.)
PARAMETER Small-Signal -3dB Bandwidth Large-Signal -3dB Bandwidth Small-Signal Bandwidth for 0.1dB Gain Flatness Large-Signal Bandwidth for 0.1dB Gain Flatness Slew Rate Settling Time to 0.1% Rise/Fall Time Spurious-Free Dynamic Range Differential Phase Error Differential Gain Error Input Noise-Voltage Density Input Noise-Current Density Input Capacitance Output Impedance Disable OFF Time Disable ON Time Channel-to-Channel Isolation CHISO SYMBOL BWSS BWLS BW0.1dBss BW0.1dBLS SR tS tR/tF SFDR DP DG en in CIN ZOUT f = 5MHz MAX4389/MAX4393/MAX4394/MAX4396 MAX4389/MAX4393/MAX4394/MAX4396 MAX4392/MAX4393/MAX4394/MAX4395/ MAX4396, specified at DC VOUT = 2VP-P VOUT = 100mVP-P VOUT = 2VP-P VOUT = 2V step VOUT = 2V step VOUT = 100mVP-P fC = 5MHz, VOUT = 2VP-P NTSC, RL = 150 NTSC, RL = 150 f = 10kHz f = 10kHz CONDITIONS VOUT = 100mVP-P MIN TYP 85 90 27 24 500 21 4 -59 0.015 0.015 13 2.1 1 0.6 80 40 -97 MAX UNITS MHz MHz MHz MHz V/s ns ns dBc degrees % nV/Hz pA/Hz pF ns ns dB
Note 2: All devices are 100% production tested at TA = +25C. Specifications over temperature limits are guaranteed by design.
_______________________________________________________________________________________
5
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Typical Operating Characteristics
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)
GAIN AND PHASE vs. FREQUENCY
80 60 40 20 GAIN (dB) 0 -20 -40 -60 -80 -100 -120 1k 10k 100k 1M 10M 100M 1G FREQUENCY (Hz) PHASE GAIN
MAX4389 toc01
SMALL-SIGNAL GAIN vs. FREQUENCY
MAX4389 toc02
LARGE-SIGNAL GAIN vs. FREQUENCY
3 2 1 GAIN (dB) 0 -1 -2 -3 -4 -5 -6 VOUT = 2VP-P
MAX4389 toc03
180 135 90 PHASE (DEGREES) GAIN (dB) 45 0 -45 -90 -135 -180 -225 -270
4 3 2 1 0 -1 -2 -3 -4 -5 -6
4
VOUT = 100mVP-P
100k
1M
10M FREQUENCY (Hz)
100M
1G
100k
1M
10M FREQUENCY (Hz)
100M
1G
SMALL-SIGNAL GAIN FLATNESS vs. FREQUENCY
MAX4389 toc04
LARGE-SIGNAL GAIN FLATNESS vs. FREQUENCY
0.3 0.2 0.1 GAIN (dB) 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 0.01 100k 1M 10M FREQUENCY (Hz) 100M 1G VOUT = 2VP-P
MAX4389 toc05
OUTPUT IMPEDANCE vs. FREQUENCY
MAX4389 toc06
0.4 0.3 0.2 0.1 GAIN (dB) 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6
VOUT = 100mVP-P
0.4
100
OUTPUT IMPEDANCE ()
10
1
0.1
100k
1M
10M FREQUENCY (Hz)
100M
1G
100k
1M
10M FREQUENCY (Hz)
100M
1G
DISTORTION vs. FREQUENCY
MAX4389 toc07
DISTORTION vs. FREQUENCY
MAX4389 toc08
DISTORTION vs. FREQUENCY
-10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 2ND HARMONIC 3RD HARMONIC VOUT = 2VP-P, AVCL = 5V/V
MAX4389 toc09
0 -10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 100k 1M 10M 3RD HARMONIC 2ND HARMONIC VOUT = 2VP-P, AVCL = 1V/V
0 -10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 3RD HARMONIC 2ND HARMONIC VOUT = 2VP-P, AVCL = 2V/V
0
100M
100k
1M
10M
100M
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FREQUENCY (Hz)
6
_______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Typical Operating Characteristics (continued)
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)
DISTORTION vs. RESISTIVE LOAD
MAX4389 toc10
DISTORTION vs. VOLTAGE SWING
DIFF GAIN (%) -10 -20 DISTORTION (dBc) -30 -40 -50 DIFF PHASE () -60 -70 -80 3RD HARMONIC 2ND HARMONIC fo = 5MHz, AVCL = 1V/V
MAX4389 toc11
DIFFERENTIAL GAIN AND PHASE
0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 0.5 0.4 0.3 0.2 0.1 0 -0.1 0 1 RL = 150 TO GND, AVCL = 2V/V
MAX4389 toc12
0 -10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 -80 -90 -100 0 200 400 600 800 1000 3RD HARMONIC 2ND HARMONIC fo = 5MHz, VOUT = 2VP-P, AVCL = 1V/V
0
-90 -100 1200 0.5 1.0 1.5 2.0
RL = 150 TO GND, AVCL = 2V/V 2 3 IRE 4 5 6
VOLTAGE SWING (VP-P)
VOLTAGE SWING (VP-P)
COMMON-MODE REJECTION vs. FREQUENCY
MAX4389 toc13
POWER-SUPPLY REJECTION vs. FREQUENCY
MAX4389 toc14
OUTPUT VOLTAGE SWING vs. RESISTIVE LOAD
1.4 OUTPUT VOLTAGE SWING (V) 1.2 1.0 0.8 0.6 0.4 0.2 VOL- VEE 0 VCC - VOH
MAX4389 toc15
0 -10 -20 GAIN (dB)
0 -10 -20 PSR (dB) -30 -40 -50 -60 -70
1.6
-30 -40 -50 -60 -70 -80 100k 1M 10M FREQUENCY (Hz) 100M 1G
100k
1M
10M FREQUENCY (Hz)
100M
1G
0
100
200
300 RLOAD ()
400
500
600
SMALL-SIGNAL PULSE RESPONSE
AVCL = 1V/V INPUT 50mV/div
MAX4389 toc16
SMALL-SIGNAL PULSE RESPONSE
AVCL = 2V/V AVCL = +2V/V RF = 200 RF = 200 INPUT 25mV/div
MAX4389 toc17
SMALL-SIGNAL PULSE RESPONSE
AVCL = 5V/V RF = 250 INPUT 10mV/div
MAX4389 toc18
OUTPUT 50mV/div
OUTPUT 50mV/div
OUTPUT 50mV/div
20ns/div
20ns/div
20ns/div
_______________________________________________________________________________________
7
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Typical Operating Characteristics (continued)
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)
LARGE-SIGNAL PULSE RESPONSE
MAX4389 toc19
LARGE-SIGNAL PULSE RESPONSE
AVCL = 2V/V RF = 200 INPUT 250mV/div
MAX4389 toc20
LARGE-SIGNAL PULSE RESPONSE
AVCL = 5V/V RF = 250 INPUT 100mV/div
MAX4389 toc21
AVCL = 1V/V INPUT 500mV/div
OUTPUT 500mV/div
OUTPUT 500mV/div
OUTPUT 500mV/div
20ns/div
20ns/div
20ns/div
VOLTAGE NOISE vs. FREQUENCY
MAX4389 toc22
CURRENT NOISE vs. FREQUENCY
MAX4389 toc23
ISOLATION RESISTANCE vs. CAPACITIVE LOAD
5 4 3 2 GAIN (dB) 1 0 -1 -2 -3 -4 100pF
MAX4389 toc24
1000 RL = 100 VOLTAGE NOISE (nV/Hz)
1000 RL = 100 CURRENT NOISE (pA/Hz)
6
100
100
68pF
33pF
10
10
1 1 10 100 1k 10k 100k FREQUENCY (Hz)
1 1 10 100 1k 10k 100k FREQUENCY (Hz)
-5 -6 100k 1M 10M FREQUENCY (Hz) 100M 1G
8
_______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Typical Operating Characteristics (continued)
(VCC = 5V, VEE = -5V, VCM = 0V, AVCL = 1V/V, RL = 100 to GND, GND = 0, TA = +25C, unless otherwise noted.)
SMALL-SIGNAL BANDWIDTH vs. LOAD RESISTANCE
MAX4389 toc25
OPEN-LOOP GAIN vs. RESISTIVE LOAD
MAX4389 toc26
CROSSTALK vs. FREQUENCY
-10 -20 CROSSTALK (dB) -30 -40 -50 -60 -70 -80 -90 -100
MAX4389 toc27
140 120 BANDWIDTH (MHz) 100 80 60 40 20 0 0
80 70 OPEN-LOOP GAIN (dBc) 60 50 40 30 20 10 0
0
100 200 300 400 500 600 700 800 RLOAD ()
100
1k RLOAD ()
10k
100k
1M
10M FREQUENCY (Hz)
100M
1G
DISABLE RESPONSE
MAX4389 toc28
INPUT OFFSET VOLTAGE vs. TEMPERATURE
MAX4389 toc29
INPUT BIAS CURRENT vs. TEMPERATURE
7 INPUT BIAS CURRENT (A) 6 5 4 3 2 1 0 -50 -25 0 25 50 75 100
MAX4389 toc30
8 7 INPUT OFFSET VOLTAGE (mV) 6 5 4 3 2 1 0
8
5V DISABLE 0V
1.5V VOUT 0V 200ns/div
-50
-25
0
25
50
75
100
TEMPERATURE (C)
TEMPERATURE (C)
SUPPLY CURRENT vs. TEMPERATURE
7 SUPPLY CURRENT (mA) 6 5 4 3 2 1 0 -50 -25 0 25 50 75 100 TEMPERATURE (C)
MAX4389 toc31
8
_______________________________________________________________________________________
9
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Pin Description
PIN MAX4389 SC70/SOT23 1 MAX4390 SC70 1 SOT23 1 MAX4392 MAX/SO -- MAX4393 MAX -- MAX4394 SO/TSSOP -- MAX4395 SO/TSSOP -- MAX4396 TSSOP -- OUT Amplifier Output Negative Power Supply. Connect a 0.1F Capacitor to GND. Noninverting Input Inverting Input Disable. Connect to VCC to Enable. Positive Power Supply. Connect a 0.1F Capacitor to GND. No Connection. Not Internally Connected. Amplifier A Noninverting Input Amplifier A Inverting Input Amplifier A Output Shutdown Amplifier A. Connect to VCC to Enable. Amplifier B Noninverting Input Amplifier B Inverting Input Amplifier B Output NAME FUNCTION
2
2
2
4
4
11
11
16
VEE
3 4 5
3 4 --
3 4 --
-- -- --
-- -- --
-- -- --
-- -- --
-- -- --
IN+ INDISABLE
6
6
5
8
10
4
4
5
VCC
--
5
--
--
--
--
--
10, 11
N.C.
--
--
--
3
3
5
3
4
INA+
-- --
-- --
-- --
2 1
2 1
6 7
2 1
3 2
INAOUTA
--
--
--
--
5
1
--
1
DISABLEA
--
--
--
5
7
10
5
6
INB+
-- --
-- --
-- --
6 7
8 9
9 8
6 7
7 8
INBOUTB
10
______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
Pin Description (continued)
PIN MAX4389 SC70/SOT23 MAX4390 SC70 SOT23 MAX4392 MAX/SO MAX4393 MAX MAX4394 SO/TSSOP MAX4395 SO/TSSOP MAX4396 TSSOP Shutdown Amplifier B. Connect to VCC to Enable. Amplifier C Noninverting Input Amplifier C Inverting Input Amplifier C Output Shutdown Amplifier C. Connect to VCC to Enable. Amplifier D Noninverting Input Amplifier D Inverting Input Amplifier D Output Shutdown Amplifier D. Connect to VCC to Enable. NAME FUNCTION
MAX4389/MAX4390/MAX4392-MAX4396
--
--
--
--
6
3
--
9
DISABLEB
--
--
--
--
--
12
10
15
INC+
-- --
-- --
-- --
-- --
-- --
13 14
9 8
14 13
INCOUTC
--
--
--
--
--
2
--
12
DISABLEC
--
--
--
--
--
--
12
17
IND+
-- --
-- --
-- --
-- --
-- --
-- --
13 14
18 19
INDOUTD
--
--
--
--
--
--
--
20
DISABLED
Detailed Description
The MAX4389/MAX4390/MAX4392-MAX4396 are dualsupply, rail-to-rail, voltage-feedback amplifiers that employ current-feedback techniques to achieve 500V/s slew rates and 85MHz bandwidths. Excellent harmonic distortion and differential gain/phase performance make these amplifiers an ideal choice for a wide variety of video and RF signal-processing applications.
gain sensitivity to load variations. The input stage permits common-mode voltages to the negative supply and to within 2.25V of the positive supply rail.
Choosing Resistor Values
Unity-Gain Configuration The MAX4389/MAX4390/MAX4392-MAX4396 are internally compensated for unity gain. When configured for unity gain, a 24 resistor (RF) in series with the feedback path optimizes AC performance. This resistor improves AC response by reducing the Q of the parallel LC circuit formed by the parasitic feedback capacitance and inductance.
Applications Information
The output voltage swings to within 200mV of each supply rail. Local feedback around the output stage ensures low open-loop output impedance to reduce
______________________________________________________________________________________
11
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Video Line Driver The MAX4389/MAX4390/MAX4392-MAX4396 are lowpower, voltage-feedback amplifiers featuring large-signal (2V P-P) bandwidths of 90MHz and 0.1dB largesignal gain flatness of 24MHz. They are designed to minimize differential-gain error and differential-phase error to 0.015% and 0.015, respectively. They have a 21ns settling time to 0.1%, 500V/s slew rates, and output-current-drive capability of up to 50mA making them ideal for driving video loads. Inverting and Noninverting Configurations Select the gain-setting feedback (RF) and input (RG) resistor values to fit your application. Large resistor values increase voltage noise and interact with the amplifier's input and PC board capacitance. This can generate undesirable poles and zeros and decrease bandwidth or cause oscillations. For example, a noninverting gain-of-two configuration (RF = RG) using 2k resistors, combined with 1pF of amplifier input capacitance and 1pF of PC board capacitance, causes a pole at 79.6MHz. Since this pole is within the amplifier bandwidth, it jeopardizes stability. Reducing the 2k resistors to 100 extends the pole frequency to 1.59GHz, but could limit output swing by adding 200 in parallel with the amplifier's load resistor (Figures 1a and 1b).
Layout and Power-Supply Bypassing
The MAX4389/MAX4390/MAX4392-MAX4396 operate from single 4.5V to 11V or from dual 2.25V to 5.5V supplies. Bypass each supply with a 0.1F capacitor as close to the pin as possible. Maxim recommends using microstrip and stripline techniques to obtain full bandwidth. To ensure that the PC board does not degrade the amplifier's performance, design it for a frequency greater than 1GHz. Pay careful attention to inputs and outputs to avoid large parasitic capacitance. Whether or not you use a constant-impedance board, observe the following design guidelines: * Do not use wire-wrap boards; they are too inductive. * * * * Do not use IC sockets; they increase parasitic capacitance and inductance. Use surface-mount instead of through-hole components for better, high-frequency performance. Use a PC board with at least two layers; it should be as free from voids as possible. Keep signal lines as short and as straight as possible. Do not make 90 turns; round all corners.
Low-Power Disable Mode
The MAX4389/MAX4393/MAX4394/MAX4396 feature a disable function that allows the amplifiers to be placed in a low-power, high-output-impedance state. When the disable pin (DISABLE) is active, the amplifier's output impedance is 95k. This high resistance and the low 2pF output capacitance make the MAX4389/ MAX4390/MAX4392-MAX4396 in RF/video multiplexer or switch applications. For larger arrays, pay careful attention to capacitive loading (see the Output Capacitive Loading and Stability section).
RG
RF
MAX43_ _
VOUT
VIN
VOUT = [1 + (RF / RG)] VIN
Output Capacitive Loading and Stability
Figure 1a. Noninverting Gain Configuration
RG VIN
RF
MAX43_ _
VOUT
VOUT = -(RF / RG) VIN
Figure 1b. Inverting Gain Configuration
The MAX4389/MAX4390/MAX4392-MAX4396 are optimized for AC performance. They are not designed to drive highly reactive loads, which decrease phase margin and may produce excessive ringing and oscillation. Figure 2 shows a circuit that eliminates this problem. Figure 3 is a graph of the Optimal Isolation Resistor (RS) vs. Capacitive Load. Figure 4 shows how a capacitive load causes excessive peaking of the amplifier's frequency response if the capacitor is not isolated from the amplifier by a resistor. A small isolation resistor (usually 10 to 15) placed before the reactive load prevents ringing and oscillation. At higher capacitive loads, AC performance is controlled by the interaction of the load capacitance and the isolation resistor. Figure 5 shows the effect of a 15 isolation resistor on closed-loop response.
12
______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
RG RF
6 5
RISO
4
VOUT
MAX438 _
GAIN (dB)
VIN
3 2 1 0 -1 -2 -3 -4 -5 -6 100k 1M
CL
120pF
68pF
Figure 2. Driving a Capacitive Load Through an Isolation Resistor
180pF
16 15 14 RISO () 13 12 11 10 9 0 50 100 150 200 250 300 350 400 450 500 550 CLOAD (pF) SMALL SIGNAL (VOUT = 100mVP-P) LARGE SIGNAL (VOUT = 2VP-P)
10M FREQUENCY (Hz)
100M
1G
Figure 5. Small-Signal Gain vs. Frequency with Load Capacitance and 27 Isolation Resistor
Chip Information
MAX4389 TRANSISTOR COUNT: 70 MAX4390 TRANSISTOR COUNT: 70 MAX4392 TRANSISTOR COUNT: 204 MAX4393 TRANSISTOR COUNT: 204 MAX4394 TRANSISTOR COUNT: 298 MAX4395 TRANSISTOR COUNT: 396 MAX4396 TRANSISTOR COUNT: 396 PROCESS: BiCMOS
Figure 3. Isolation Resistance vs. Capacitive Load
6 5 4 3 2 GAIN (dB) 1 0 -1 -2 -3 -4 -5 -6 100k 1M
100pF
68pF
33pF
10M FREQUENCY (Hz)
100M
1G
Figure 4. Small-Signal Gain vs. Frequency with Load Capacitance and No Isolation Resistor
______________________________________________________________________________________ 13
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Pin Configurations (continued)
TOP VIEW
OUT 1 6 VCC
TOP VIEW
OUT 1 5 VCC
VEE 2
MAX4390
5
N.C.
VEE 2
MAX4390
4 IN-
IN+ 3
4
IN-
IN+ 3
SC70
SOT23
TOP VIEW
OUTA 1 INAINA+ VEE 2 3 4 8 7 VCC OUTB INBINB+
TOP VIEW
OUTA 1 INAINA+ VEE DISABLEA 2 3 4 5 10 VCC 9 OUTB INBINB+ DISABLEB
MAX4392
6 5
MAX4393
8 7 6
MAX/SO
MAX
TOP VIEW
DISABLEA 1 DISABLEC 2 DISABLEB 3 VCC 4 INA+ 5 INA- 6 OUTA 7 14 OUTC 13 INC12 INC+
TOP VIEW
OUTA 1 INAINA+ 2 3 14 OUTD 13 IND12 IND+
MAX4394
11 VEE 10 INB+ 9 8 INBOUTB
VCC 4 INB+ 5 INB- 6 OUTB 7
MAX4395
11 VEE 10 INC+ 9 8 INCOUTC
SO/TSSOP
SO/TSSOP
14
______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
Pin Configurations (continued) Ordering Information (continued)
PART TEMP RANGE -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C PINPACKAGE 8 SO 8 MAX 8 MAX 10 MAX 14 SO 14 SO 14 TSSOP 14 TSSOP 14 SO 14 SO 14 TSSOP 14 TSSOP 20 TSSOP TOP MARK -- -- -- -- -- -- -- -- -- -- -- -- --
MAX4389/MAX4390/MAX4392-MAX4396
TOP VIEW
DISABLEA 1 OUTA 2 INA- 3 INA+ 4 VCC 5 INB+ 6 INB- 7 OUTB 8 DISABLEB 9 N.C. 10
+
20 DISABLED 19 OUTD 18 IND17 IND+
MAX4392ESA+T MAX4392EUA+T MAX4392EUA/V+T MAX4393EUB+T MAX4394ESD+T MAX4394ESD/V+T MAX4394EUD+T MAX4394EUD/V+T MAX4395ESD+T MAX4395ESD/V+T MAX4395EUD+T MAX4395EUD/V+T MAX4396EUP+T
MAX4396
16 VEE 15 INC+ 14 INC13 OUTC 12 DISABLEC 11 N.C.
TSSOP
+Denotes a lead(Pb)-free/RoHs-compliant package. /V denotes an automotive qualified part. T = Tape and reel.
Selector Guide
PART MAX4389 MAX4390 MAX4392 MAX4393 MAX4394 MAX4395 MAX4396 NO. OF AMPS 1 1 2 2 3 4 4 DISABLE Yes No No Yes Yes No Yes
______________________________________________________________________________________
15
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE 6 SC70 6 SOT23 5 SOT23 8 MAX 10 MAX 8 SO, 14 SO 14 TSSOP, 20 TSSOP PACKAGE CODE X5-1 U6-1 U5-1 U8-1 U10-2 S8-2, S14-1 U14-1, U20-3 DOCUMENT NO. 21-0077 21-0058 21-0057 21-0036 21-0061 21-0041 21-0066
16
______________________________________________________________________________________
SC70, 6L.EPS
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
MAX4389/MAX4390/MAX4392-MAX4396
PACKAGE OUTLINE, SOT 6L BODY
21-0058
I
1
2
______________________________________________________________________________________
17
6LSOT.EPS
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
PACKAGE OUTLINE, SOT 6L BODY
21-0058
I
2
2
18
______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
SOT-23 5L .EPS
MAX4389/MAX4390/MAX4392-MAX4396
______________________________________________________________________________________
19
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
20
______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
10LUMAX.EPS
MAX4389/MAX4390/MAX4392-MAX4396
__________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
SOICN .EPS
INCHES DIM A A1 B C e E H L MAX MIN 0.053 0.069 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050
MILLIMETERS MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 BSC 3.80 4.00 5.80 6.20 0.40 1.27
N
E
H
VARIATIONS:
1
INCHES
MILLIMETERS MIN 4.80 8.55 9.80 MAX 5.00 8.75 10.00 N MS012 8 AA 14 AB 16 AC
TOP VIEW
DIM D D D
MIN 0.189 0.337 0.386
MAX 0.197 0.344 0.394
D A e B A1 C 0-8 L
FRONT VIEW
SIDE VIEW
PROPRIETARY INFORMATION TITLE:
PACKAGE OUTLINE, .150" SOIC
APPROVAL DOCUMENT CONTROL NO.
21-0041
REV.
B
1
1
22
______________________________________________________________________________________
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
TSSOP4.40mm.EPS
MAX4389/MAX4390/MAX4392-MAX4396
______________________________________________________________________________________
23
Ultra-Small, Low-Cost, 85MHz Op Amps with Rail-to-Rail Outputs and Disable MAX4389/MAX4390/MAX4392-MAX4396
Revision History
REVISION NUMBER 4 REVISION DATE 11/09 DESCRIPTION Added automotive qualified parts PAGES CHANGED 2, 15
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
24 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2009 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.

▲Up To Search▲

Price & Availability of MAX4394ESDT

	To Download MAX4394ESDT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .